ホンダ シビック EK用 カーボンカナードキット Honda Civic EK Carbon Canard kit

ホンダ シビック EK用  カーボンカナードキット Honda Civic EK Carbon Canard kit

¥25,300

※こちらの価格には消費税が含まれています。

再入荷のお知らせを希望する

年齢確認

再入荷されましたら、登録したメールアドレス宛にお知らせします。

メールアドレス

折返しのメールが受信できるように、ドメイン指定受信で「thebase.in」と「rizejapan.com」を許可するように設定してください。

再入荷のお知らせを希望する

再入荷のお知らせを受け付けました。

ご記入いただいたメールアドレス宛に確認メールをお送りしておりますので、ご確認ください。
メールが届いていない場合は、迷惑メールフォルダをご確認ください。
通知受信時に、メールサーバー容量がオーバーしているなどの理由で受信できない場合がございます。ご確認ください。

折返しのメールが受信できるように、ドメイン指定受信で「thebase.in」と「rizejapan.com」を許可するように設定してください。

EK9シビックタイプR後期型純正バンパー専用カーボン製カナード新品です。
商品説明
デザインは、一体感を増す為に本体、ステー部分、サイドフランジ(外側)をカーボン一体整形としました。
性能とデザインを両立させるべく、最終的にこの形になりました。
ステーと本体を一体にする事により表面にボルト、ビス、リベットなどが出ない為美しく、
しかも汎用品では出せない強度です。表面はカーボーン、クリヤーゲルコート仕上げです。
タイプRオーナーの方は実戦タイプの方が多く、空力面にも気を使われている場合も多いようです。
FF独特のアンダーステア対策に気を使い、このほどシビックR用を開発しました。
バンパーサイドからバンパー前部方向に出来るだけ伸ばし、取り付け個所を前端部まで設け、
ダウンフォースが掛かった時の上下方向のシナリを出来る限り防止し、とことん性能を追求しています。
強度は計4プライ。ステー部分とサイドフラッブ部分がリブ構造となり、剛性は十分です。
取り付けは付属の専用ビスを使用するのみなのでプラスドライバーが一本あれば取り付け可能です。
もちろんステー部分にビス用の穴も開いています。純正バンパーはウレタン製ですので下穴を開ける必要はありません。
取り付けステーなどを別途購入する必要が無く経済的です。
写真は、開発用バンパーにサンプル品をテープで仮付けしたものです。
写真をご覧いただき納得していただいた上ご入札ください。ご覧のハンパーにて開発致しましたので
それ以外のバンパーへのマッチングは取っておりません。ご了承ください。
この製品は二段仕様です。片側2枚、計4枚と専用ビスが付属します。



EK9 Civic type R Late genuine bumper 9000 Carbon steel canard is a new article.
Description of item
Design, has body, stay part, the side flange (outside) and carbon together shaped in order to increase the sense of unity.
In order to achieve both performance and design, finally it became this form.
Bolt to the surface by which the stay and the body together, bis, beautifully for such rivet does not come out,
Moreover, it is the strength that does not put out in the general-purpose products. Surface Kabon, is a clear gel coat finish.
If the Type R owners are often more of combat type, it seems in many cases also to the aerodynamic surfaces have been used to care about.
Use care to FF distinctive understeer measures, it was recently developed for the Civic R.
Stretched out as much as possible from the bumper side to bumper front direction is provided with a mounting point to the front end,
To prevent as much as possible in the vertical direction of the bending of the when the down force is applied, has been thoroughly pursued performance.
Strength is a total of 4-ply. Stay part and Saidofurabbu part becomes a rib structure, rigidity is sufficient.
Mounting can be mounted if Phillips screwdriver is by one because only use a dedicated screw which is included.
Of course, also open holes for the screws to the stay part. There is no need under pierce so genuine bumper is made of urethane.
It is required separately without economical to purchase and installation stay.
Photo is what the sample products were temporarily attached with tape to the development for the bumper.
Please bid on who to convince seeing photos. Because we have developed in the hamper of visit
Matching to it other than the bumper is not taken. Please note.
This product is a two-stage design. Two on one side, comes with a dedicated screw a total of four.

ショップの評価

関連商品


ビート チタンボンネットバー トランクバー セット Beat hood/trunk bar set titanium bar 2023

¥28,930

ホンダ シビック EG用 カーボンカナードキット Honda Civic EG Carbon Canard kit

¥19,800

Honda S2000用 チタンボンネットバー Honda S2000 titanium bar 2023

¥31,680